neighbor - The neighbor LACP information.
internal - The internal LACP information. By default, it is empty, and will displa y the information of all LACP groups. detail - The detailed information of EtherChan nel.Ģ5 Parameter channel-group-num - The EtherChannel G roup number, ranging from 1 to 6. By default, it is empty, and will displa y the information of all EtherChannel Groups. Global Configuration Mode : In this mode, global commands are provided, such as the Spanning Tree, Schedule Mode and so on.ħ 1.4 Conventions 1.4.1 Format Conventions The following conventions are used in this Guide: Items in square brackets are optional Items in braces Parameter channel-group-num - The EtherChannel G roup number, ranging from 1 to 6. To configure some commands, you should access the corres ponding command mode firstly. Each command mode has its own set of s pecific commands. Mode Accessing Path Prompt Logout or Access the next mode User EXEC Mode Primary mode once it is connected with the swi tch.Ħ 2.
#Loopback cable config how to
T ype the User name and Passwo rd (the factory default value fo r both of them is admin) and press the Enter button, then you can use the CLI now, which is shown as Figure1-4.ĥ The following table gives detailed information about the Accessing path, Prompt of each mode and how to exit the current mode and access the next mode. T ype telnet 192.168.0.1 in the command prompt shown as Figure 1-3, and press the Enter button. T o log on to the switch by a T elnet connection, please take the following steps: 1.Ĥ 4. Chapter 12: Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control, Negotiation Mode, and S torm Control for enthernet ports.ģ Chapter 1 Using the CLI 1.1 Accessing the CLI Y ou can log on to the switch and access the CLI by logging on to the switch remotely by a T elnet through an Ethernet port.
#Loopback cable config upgrade
The four devices of TL-SG2216/TL-SG2424/TL-S G2424P/TL-SG2452 are sharing this Guide.Ģ IP, reboot and reset the switch, upgrade the sw itch system and comm ands used for device diagnose, including loopback test and cable test. The device mentioned in this Guide stands for TL-SG2216/TL-SG2424 /TL-SG2424P/TL-SG2452 Gigabit Smart Switch. ġ Preface This Guide is intended for network administrator to provide referenced information about CLI (Command Line Interface). 170 show lldp neighbor-infor mation inte rface. X show lldp local-inform ation inte rface. VII Chapter 1 8 DHCP Filteri ng Comma nds. Other brands and product names are trademarks or registered trademarks of t heir respective holders. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. When you have a Layer 3 switch, like a Catalyst 4500,6500,3550 or 3750, to configure loopback interface from the config mode, complete these steps: Switchconfigure terminal. I COPYRIGHT & TRADEMARKS S pecifications are subject to change without notice. The management vlan of the switch acts like the loopback interface since they are both logical interfaces. In order to remove the loopback interface, use the no interface loopback 1 in config mode.TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452 Gigabit Smart Switch REV1.2.0 1910010910. When you have a Layer 3 switch, like a Catalyst 4500,6500,3550 or 3750, to configure loopback interface from the config mode, complete these steps: The management vlan of the switch acts like the loopback interface since they are both logical interfaces. The Layer 2 switches like 3500xl or 2950, the loopback interface is not needed since these switches are not capable of routing between interfaces.
#Loopback cable config mac
Loopback interfaces do not have internal VLAN IDs or MAC addresses. There is no limit on the number of loopback interfaces you can create. This is an issue in networks with multiple equal-cost paths because under normal circumstances the packets that are generated by a networking device use the IP address from the outbound interface as the source address for the packets and because in a network with two or more equal-cost paths from the networking device to the receiving host each packet might use a different outbound interface.
This address can be configured as the source address when the networking device needs to send data for protocols such as NetFlow,OSPF or Cisco Discovery Protocol (CDP) to another device in your network and you want the receiving device to always see the same source IP address from the networking device. A loopback interface can provide a stable interface on which you can assign a Layer 3 address.
0 kommentar(er)
